Nissan Sunny service from 1991 to 1997 of release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semi-axes
11. Brakes
12. Suspension brackets and steering
13. Body
13.1. Specifications
13.2. Maintenance
13.3. Small damages of a body
13.4. Large damages of a body
13.5. Front bumper
13.6. Rear bumper
13.7. Cowl
13.8. Cable of a drive of the lock of a cowl
13.9. Cowl lock
13.10. Doors
13.11. Internal panel of a door
13.12. Door lock, switch of the lock and handle detail
13.13. Glass of a door and window regulator
13.14. Trunk lid (sedan)
13.15. Cover of a cargo compartment (compartment and hatchback)
13.16. Lock trunk lids (sedan)
13.17. Lock of a cover of a cargo compartment and handle
13.18. Details of the central lock
13.19. External glasses
13.20. Windscreen, back glass and stationary glasses
13.21. Hatch
13.22. Decorative overlays of a body
13.23. Seats
13.24. Panels of facing of salon
13.25. Average section of the forward panel
13.26. Details of forward facing of salon
14. Electric equipment
 







13-13-steklo-dveri-i-steklopodemnik.html

13.13. Glass of a door and window regulator

Removal and installation

PERFORMANCE ORDER
Glass
1. Remove the panel and the screen.
2. Establish the window regulator handle (or attach the switch socket, connect the battery to weight).
3. Lower glass so that the bolt of the holder of glass appeared in an opening of a framework of a door.
4. Supporting glass, unscrew bolts of fastening of glass to the holder (are specified by shooters). In cars with a body of a compartment there is an additional bolt of fastening of glass to a roller of a lobby directing.
5. Get glass through an aperture.
6. Glass is established upside-down. At installation watch that the sealant did not lag behind. Before installation of the panel check window regulator work.
Window regulator (hatchback and sedan)
1. Disconnect glass from a window regulator (see above).
2. Lift glass and fix a tape or wedges, or get.
3. Disconnect electric drive sockets (if it is provided).
4. Unscrew bolts of fastening of a manual drive of a window regulator (or the electric drive) (are specified by shooters).
5. Unscrew top (a photo at the left) and bottom (a photo on the right) bolts of a regulator of a window regulator and get a regulator through a window aperture. The electric drive with cables gets together with a regulator. Previously designate an arrangement of disconnected details.
6. The window regulator assembled with a regulator and a drive is established upside-down. Before installation of the panel check window regulator work.
Compartment
1. Disconnect glass from a window regulator.
2. Disconnect electric drive sockets.
3. Unscrew bolts of the electric drive of a window regulator.
4. Unscrew bolts both directing and remove a window regulator assembled. Previously designate an arrangement of disconnected details.
5. The window regulator is established upside-down. Before installation of the panel check window regulator work.
Corner of a window of a back door – 5 dverny hatchback
1. Remove elevating section of glass.
2. Unscrew bolts and remove back directing, supporting a corner.
3. Carefully get a corner with a sealant.
4. Remove from a corner a sealant.
5. The corner is established upside-down.


13.12. Door lock, switch of the lock and handle detail

13.14. Trunk lid (sedan)