Nissan Sunny service from 1991 to 1997 of release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semi-axes
11. Brakes
12. Suspension brackets and steering
12.1. Specifications
12.2. Bearings of naves of forward wheels
12.3. Rack of a forward suspension bracket
12.4. Bottom lever
12.5. Spherical support of the bottom lever
12.6. Stabilizer of cross-section stability of a forward suspension bracket
12.7. Bearings of back wheels
12.8. Details of a back suspension bracket
12.9. Wheel
12.10. Switch of ignition and lock of blocking of a steering column
12.11. Steering column
12.12. Steering mechanism
12.13. Covers of steering transfer
12.14. Hydraulic actuator
12.15. Pump of the hydraulic booster
12.16. Tips of steering draft
13. Body
14. Electric equipment
 







12-3-stojjka-perednejj-podveski.html

12.3. Rack of a forward suspension bracket


Prevention

Shock-absorbers of racks change only in pair.


Removal

PERFORMANCE ORDER
1. Lift a forward part of the car and establish on supports.
2. Remove a wheel.
3. Disconnect from a rack a hydraulic actuator tube.
4. Unscrew two nuts of fastening of a rack to a rotary fist (are specified by shooters) and disconnect a rack.
5. Ask the assistant to support a rack from below, and unscrew three nuts of fastening of a rack to a cap of a mudguard of a motor compartment (are specified by shooters).

Prevention

The central nut not to turn on! Get a rack through a motor compartment.



Dismantling

PERFORMANCE ORDER
1. Clamp the lower part of a rack in a vice through laying.
2. Screw nuts and упершись in hairpins the lever, unscrew the top nut of a rod of the shock-absorber. Completely a nut not to turn on.
3. Compress a spring by means of the adaptation so that the top plate could rotate by hand.
4. Turn out a rod nut, holding a rod from a provorachivaniye.
5. Remove a washer, laying, the top cap.
6. Remove the plug, the bearing, the top plate of a spring and the rubber buffer of a plate. Pay attention to an order of installation of details.
7. Get a spring, a dust cover, the rubber buffer and a plate.
8. Check a condition of details, especially rubber buffers. If necessary replace.
9. Check existence of a leak from the shock-absorber and a rod condition on all length.
10. Check existence on the case of cracks and damages.
11. Check rack work, at first having put forward a rod for all length, and then moving and putting forward a rod on length of 50-00 mm. Smooth resistance to rod moving should be felt.
12. If traces of a leak, mechanical damages are observed, and movement of a rod is accompanied by "breakthroughs", the rack is subject to replacement.
13. It is possible to establish a spring and all details on a new rack.
14. Examine a spring.
15. If strong corrosion of a spring, a crack on rounds, deformation or any signs of a doubtful condition are found, replace a spring.
16. Clamp a rack in a vice and establish the rubber buffer a plate and a dust cover.
17. Compress a spring and establish in a plate. At installation the termination of a round should come into deepening of a plate (shooter).
18. Establish the top buffer and a plate, having correctly arranged a spring round in a plate. At installation of a rack of the shooter on the top plate it should be turned in the cross-section direction outside (And – towards a forward part, In – the cross-section direction).
19. Establish the bearing, the plug and the top cap.
20. Replace a nut and a rod washer, tighten a nut with the set moment, holding a rod.
21. Remove the adaptation for spring compression.
22. Establish a cap of a nut of a rod.

Installation

PERFORMANCE ORDER
1. Establish new laying of the top fastening of a rack.
2. Establish a rack so that hairpins entered into mudguard openings, and cut and the shooter on the top plate were turned in the cross-section direction outside.
3. Tighten nuts with the set moment.
4. Combine openings in a rack and a rotary fist, tighten new nuts and bolts with the set moment (nuts should be turned on a car course).
5. Fix a hose a bracket on a rack.
6. Establish an arm of conducting of the sensor of speed (on cars with ABS system).
7. Establish a wheel and lower the car.


12.2. Bearings of naves of forward wheels

12.4. Bottom lever