Nissan Sunny service from 1991 to 1997 of release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semi-axes
11. Brakes
12. Suspension brackets and steering
12.1. Specifications
12.2. Bearings of naves of forward wheels
12.3. Rack of a forward suspension bracket
12.4. Bottom lever
12.5. Spherical support of the bottom lever
12.6. Stabilizer of cross-section stability of a forward suspension bracket
12.7. Bearings of back wheels
12.8. Details of a back suspension bracket
12.9. Wheel
12.10. Switch of ignition and lock of blocking of a steering column
12.11. Steering column
12.12. Steering mechanism
12.13. Covers of steering transfer
12.14. Hydraulic actuator
12.15. Pump of the hydraulic booster
12.16. Tips of steering draft
13. Body
14. Electric equipment
 







12-2-podshipniki-stupic-perednikh-koles.html

12.2. Bearings of naves of forward wheels

Replacement

PERFORMANCE ORDER
1. Lift a forward part of the car and establish on supports.
2. Remove a wheel.
3. Remove a disk and a support.
4. Remove the sensor of speed (on cars with ABS system).
5. Unscrew fastenings of an arm of conducting and take the sensor aside.
6. Disconnect a semi-axis from only from a nave, take aside and fix (see subsection 10.2).
7. Unscrew two nuts of fastening of a rack to a rotary fist (are specified by shooters), get bolts and disconnect a rack.
8. Rasshplintuyte also unscrew nuts, выпрессуйте a spherical support and a tip of steering draft from fist eyes.
9. Vypressuyte a nave from the bearing. On a nave there should be one of internal holders of the bearing.
10. Press a bearing holder from a nave.
11. Get an external epiploon.
12. Get an internal epiploon.
13. Get from an opening in a fist under the bearing a lock ring.
14. If landing of the remained holder weakened, get a holder.
15. Vypressuyte the bearing from a fist an opravka of suitable diameter which rests only against an external part of the bearing.
16. At a vypressovka it is necessary to rest a back part of a fist.
17. Выпрессовать the bearing it is possible also in blows on the inserted internal holder through a tubular opravka.

Installation

PERFORMANCE ORDER
1. Before installation of the new bearing carefully clear an internal surface of a fist.
2. Press an external holder of the bearing, resting an opravka only against an external edge. It is forbidden to grease an external part of a holder for simplification of a press fitting.
3. Insert into a flute in a fist opening a lock ring.
4. Put greasing in a cavity of an epiploon and carefully press an epiploon from the outer side of a rotary fist.
5. Establish a prop of an external part of a fist.
6. Put greasing in an epiploon and press an epiploon from the interior of a fist.
7. Having reliably rested an internal holder of the bearing, carefully press a nave in a fist.
8. Check freedom of rotation of a nave.
9. Attach a semi-axis and tighten a nut with the set moment.
10. Dress a disk and a brake support.
11. Attach a spherical support of the bottom lever, wrap a new nut and tighten with the set moment.
12. Zashplintuyte nut new shplinty.
13. Attach a rack, having replaced bolts and nuts.
14. Tighten bolts and nuts with the set moment.
15. Attach steering draft, having replaced a nut and шплинт.
16. Establish a wheel and lower the car.


12.1. Specifications

12.3. Rack of a forward suspension bracket