Nissan Sunny service from 1991 to 1997 of release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semi-axes
11. Brakes
11.1. Specifications
11.2. Hydraulic actuator of brakes
11.3. Tubes and hoses
11.4. Blocks
11.5. Brake disk
11.6. Drums
11.7. Support of a forward brake
11.8. Support of a back brake
11.9. Wheel cylinder
11.10. Main cylinder
11.11. Brake pedal
11.12. Vacuum amplifier of brakes
11.13. Amplifier of brakes and return valve
11.14. Lever of the hand brake
11.15. Cables of the hand brake
11.16. Adjustment of the hand brake
11.17. Switch of a signal of braking
11.18. Switch of a lamp of the hand brake
11.19. Anti-blocking system
12. Suspension brackets and steering
13. Body
14. Electric equipment
 







11-8-support-zadnego-tormoza.html

11.8. Support of a back brake

Removal

PERFORMANCE ORDER
1. Lift a back part of the car and establish on supports.
2. Remove a wheel.
3. Release a cover of a cable of the hand brake, disconnect a cable from the lever on a support.
4. For decrease in losses of liquid densely wrap a stopper of a tank having laid a polyethylene film, or press hoses.
5. Clear the ring union of a hose and unscrew a bolt, muffle openings.
6. Remove two laying.
7. Remove blocks.
8. Unscrew a bolt of the top finger of a support.
9. Remove a support from an arm.
10. If necessary it is possible to remove a support arm from a pin.

Dismantling

PERFORMANCE ORDER
1. Carefully clear a support.
2. Get fingers for heads of bolts which screw in fingers.
3. Remove rubber covers of fingers.
4. Turn out (to rotate counter-clockwise) and get the piston from the cylinder.
5. Remove a cover.
6. Compress a cylinder spring, having pressed on a cap, and take a lock ring from a cylinder flute.
7. Gradually releasing a spring, get a spring ring, a cap, a spring, a lock plate, a pusher and a strut.
8. A wooden stick get a cylinder sealant.
9. Unhook a spring from the lever of the hand brake, unscrew a nut and remove the lever from a support.
10. Wash out all details in pure brake liquid or alcohol.
11. All a sealant and covers are subject to obligatory replacement.
12. Check a support condition, especially carefully examine the piston and an internal surface of the cylinder, worn-out details replace. The support or a support arm separately in the spare part are not delivered.
13. Minor defects on the cylinder are eliminated with polishing by a small skin whereas the piston with the same defects is subject to obligatory replacement. To polish the piston it is forbidden.
14. Check a condition of carvings on support fingers, люфт fingers in a support should be absent.
15. Blow channels of brake liquid.
16. Before assembly check purity of all details.
17. Dress a new cover on the clown of the lever of the hand brake.
18. Establish a spring, a washer and tighten a nut.
19. Grease the clown with brake liquid and establish on a support.
20. Be convinced that at lever turn the groove in the clown is combined with an opening in a pusher.
21. Dress a lever spring.
22. Dip a new sealant of the cylinder into liquid and establish in a cylinder flute.
23. Dress on a pusher a new sealing ring and grease with rubber oil a strut and a pusher.
24. Establish all details in a support.
25. Establish a lock plate so that the groove fell on a flat part of a pusher, and camber coincided with deepening in a support.
26. Establish a spring lock ring.
27. Establish a spring and a cap, compress a spring and establish a spring lock ring.
28. Grease an edge of a cover of the cylinder with rubber oil and dress on the piston.
29. Grease with brake liquid the piston and cylinder walls in a support, screw the piston in the cylinder, rotating clockwise.
30. Dress the second edge of a cover on a support.
31. Dress new covers on support fingers.
32. Replace the rubber plug on the top finger.
33. Before installation in a support grease fingers with brake liquid.

Installation

PERFORMANCE ORDER
1. Establish a support arm on a pin, tighten bolts.
2. Establish a support, grease a carving of a bolt of the top finger with fixing structure and wrap a bolt with the set moment.
3. Establish blocks.
4. Check freedom of moving of a support in an arm.
5. Attach a hose, having established two laying and having tightened a bolt of the ring union.
6. Attach a cable of the hand brake to the lever, establish an arm. On a part of cars insert a cable cover into a bracket, and a ledge on an arm combine with dredging on a support body.
7. Remove polyethylene laying from a tank stopper (or remove collars from hoses).
8. Remove air from a hydraulic actuator of a brake of a wheel (if integrity of other contours was not broken).
9. Press several times a brake pedal.
10. Establish wheels, lower the car.
11. Before departure check work of brakes.


11.7. Support of a forward brake

11.9. Wheel cylinder