Nissan Sunny service from 1991 to 1997 of release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semi-axes
11. Brakes
11.1. Specifications
11.2. Hydraulic actuator of brakes
11.3. Tubes and hoses
11.4. Blocks
11.5. Brake disk
11.6. Drums
11.7. Support of a forward brake
11.8. Support of a back brake
11.9. Wheel cylinder
11.10. Main cylinder
11.11. Brake pedal
11.12. Vacuum amplifier of brakes
11.13. Amplifier of brakes and return valve
11.14. Lever of the hand brake
11.15. Cables of the hand brake
11.16. Adjustment of the hand brake
11.17. Switch of a signal of braking
11.18. Switch of a lamp of the hand brake
11.19. Anti-blocking system
12. Suspension brackets and steering
13. Body
14. Electric equipment
 







11-5-disk-tormoza.html

11.5. Brake disk

DISKS OF FORWARD BRAKES


Prevention

Disks change only in pair and with a set of blocks.


Check

PERFORMANCE ORDER
1. Lift a forward part of the car and establish on supports.
2. Remove wheels.
3. Slowly rotating, check a disk condition, if necessary remove blocks.
4. The disk is subject to replacement at existence on it of cracks and traces of deep development.
5. If on a disk the fillet caused by wear was formed, it is necessary to measure thickness of a disk.
6. The thickness is measured in several places, both in a place of contact with blocks, and on edge.
7. If the thickness is equal in places of wear limiting or less, the disk is subject to replacement.
8. Check adjustment of the bearing of a nave then check disk palpation by means of the indicator or laying щупы, for example between a disk and a support arm.
9. If palpation exceeds norm, remove a disk, overturn and again establish on a nave.
10. If palpation again exceeds norm, a disk replace.
11. Check a disk condition in places of fastening, damages to other places.

Removal

PERFORMANCE ORDER
1. Lift the car and remove a wheel.
2. Unscrew two bolts on a support arm, get a support, take aside and fix.
3. If the disk does not change, put labels of mutual orientation to a disk and a nave.
4. Remove a disk from hairpins of fastening of a wheel.
5. If the disk does not give in to removal, displace it, evenly wrapping bolts М8 in special carving openings.

Installation

PERFORMANCE ORDER
1. Clear demountable surfaces of a nave and a disk.
2. Establish a disk, having combined the put labels (if the removed disk is established).
3. From a new disk remove preservative.
4. Establish a support, wrap bolts with the set moment.
5. Press several times a brake pedal.
6. Establish a wheel, lower the car. Before departure check work of brakes.

DISKS OF BACK BRAKES


Prevention

Disks change only in pair and with a set of blocks.


Check

PERFORMANCE ORDER
1. Lift a back part of the car and establish on supports.
2. Remove wheels.
3. Release the hand brake.
4. Execute the actions described above. If blocks act in film, be guided by the description in subsection 11.4.2.

Removal

PERFORMANCE ORDER
1. Lift a back part of the car and establish on supports.
2. Remove wheels.
3. Unscrew bolts and remove an arm of a cable of the hand brake.
4. Disconnect a cable from the lever on a support (on a part of cars get a cable cover from a bracket).
5. Execute the actions described above.

Installation

PERFORMANCE ORDER
1. Execute the actions described above.
2. Attach a cable to the lever.
3. On a part of cars insert a cable cover into a bracket, and a ledge on an arm combine with dredging on a support body.
4. Turn on the hand brake until the necessary gap between blocks and a disk will be established.
5. Press several times a brake pedal.
6. Establish a wheel, lower the car.
7. Before departure check work of brakes.


11.4.3. Blocks of back drum-type brakes

11.6. Drums