Nissan Sunny service from 1991 to 1997 of release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semi-axes
11. Brakes
11.1. Specifications
11.2. Hydraulic actuator of brakes
11.3. Tubes and hoses
11.4. Blocks
11.5. Brake disk
11.6. Drums
11.7. Support of a forward brake
11.8. Support of a back brake
11.9. Wheel cylinder
11.10. Main cylinder
11.11. Brake pedal
11.12. Vacuum amplifier of brakes
11.13. Amplifier of brakes and return valve
11.14. Lever of the hand brake
11.15. Cables of the hand brake
11.16. Adjustment of the hand brake
11.17. Switch of a signal of braking
11.18. Switch of a lamp of the hand brake
11.19. Anti-blocking system
12. Suspension brackets and steering
13. Body
14. Electric equipment
 







11-10-glavnyjj-cilindr.html

11.10. Main cylinder

Removal

PERFORMANCE ORDER
1. Unscrew a stopper and remove liquid from a nutritious tank (or extort, having unscrewed the union on a wheel).
2. Disconnect wires from the sensor of level of liquid.
3. Clear the union on the main cylinder.
4. Designate the union that at assembly to attach on former places.
5. Unscrew nuts of unions, carefully get tubes and muffle openings.
6. Immediately wipe the spilled liquid.
7. Unscrew nuts and remove the main cylinder from the vacuum amplifier.
8. Remove from the cylinder laying.

Dismantling


Prevention

Before dismantling get ремкомплект to the cylinder of that type which is established on your car.


PERFORMANCE ORDER
1. Remove a nutritious tank, get a tank sealant (if it is provided).
2. Unbend ears and remove a cap.
3. On cars with ABS system push the first piston a wooden opravka and unscrew a lock bolt.
4. Get a lock ring (if it is provided).
5. Get from the cylinder a washer, pistons, springs and plates, having remembered an order of their installation. If necessary вытолкните the piston a stream of the compressed air, having clamped the cylinder in a vice.
6. Carefully wash out all details in alcohol or brake liquid and immediately dry.
7. Check a condition of details, at detection of wear or damages replace. Keep in mind that in ремкомплект the main cylinder pistons with sealants enter, a sealant separately in the spare part are not delivered.
8. If on the cylinder and the piston there are teases, scratches or corrosion traces, replace the cylinder assembled.
9. Before assembly grease the piston, cuffs and the cylinder with brake liquid.
10. Establish in the cylinder all details in a former order.
11. The piston enter roundabouts not to damage a cuff.
12. Establish a washer on an end face of the first piston. On cars with ABS system the lock bolt should coincide with a groove in the second piston.
13. On cars with ABS system compress pistons and wrap a lock bolt.
14. Compress pistons and fix a new cap (it is delivered in ремкомплекте).
15. Bend cap ears.
16. Check a condition of sealants of a tank, if necessary replace.
17. Dress a sealant and establish a tank.

Installation
PERFORMANCE ORDER
1. Wipe surfaces of the cylinder and the vacuum amplifier and dress new laying.
2. Establish the cylinder on the vacuum amplifier, having convinced. that the pusher of the amplifier enters into the cylinder on the center.
3. Tighten nuts with the set moment.
4. Establish tubes on the put labels, turn and tighten the union.
5. Fill in liquid in a tank and remove air from a hydraulic actuator.
6. Before departure check work of brakes.



11.9. Wheel cylinder

11.11. Brake pedal